Services available within whole-home surge protector installation
Whole-Home Surge Protector Installation includes a defined group of related evaluation, repair, installation and coordination services. Landmark selects only the services supported by the property, equipment and approved project objective.
The written option identifies which services apply, what Landmark supplies, known access limits and any customer, utility, manufacturer or other-trade responsibility before work moves forward.
- SPD type and rating.
- Conductor routing.
- Breaker connection.
- Status indication.
- Applicable service/feeder rules.
- Whole-Home Surge Protector Installation evaluation and project-fit review.
- Existing surge protection system and capacity review.
- Repair, correction or replacement options based on field findings.
- Code, equipment-listing and manufacturer-instruction review for the approved scope.
What whole-home surge protector installation includes
Whole-Home Surge Protector Installation addresses install service- or panel-level surge protective devices. Landmark confirms the actual equipment, circuit, route and property conditions before finalizing the repair or installation method.
The approved proposal identifies the work Landmark supplies, the equipment or information the customer must provide, known access limits and any permit, inspection, utility or other-trade coordination required.
- SPD type and rating.
- conductor routing.
- breaker connection.
- status indication.
- applicable service/feeder rules.
When to request this service
Request an evaluation when the condition is active, when an inspection or equipment change identifies the need, or before purchasing products that depend on electrical capacity and installation conditions.
- Install service- or panel-level surge protective devices.
- No whole-home surge protective device is installed
- A service or panel project triggers a power-protection review
- Sensitive appliances or controls have experienced suspected surge damage
Safety hazards and system implications
The visible whole-home surge protector installation need may involve the source, protection, conductors, connections, grounding, controls or connected equipment. Landmark follows the relevant electrical path so the option addresses the supported condition rather than only the symptom.
Important boundary: Plug strips are discussed as supplemental, not equivalent.
- Transient overvoltage can damage electronics, controls and insulation without tripping a standard breaker
- A surge device cannot correct poor grounding, loose service connections or sustained abnormal voltage
- Conductor length and connection location affect surge-device performance
- No surge protective device guarantees protection from every event or a direct lightning strike
How Landmark approaches the work
The exact test and installation steps depend on the property, but the service process remains clear and documented.
- Identify the service and distribution equipment to be protected
- Review available connection points and the existing grounding and bonding condition
- Select a listed device suited to the system and installation point
- Install with short, orderly conductors and required overcurrent protection
- Verify status indication and document the installed device
- Explain layered point-of-use protection and replacement indicators
Scope, access and project variables
The primary included scope covers sPD type and rating; conductor routing; breaker connection; status indication; applicable service/feeder rules. Final requirements depend on the adopted code, Michigan amendments, local authority, utility rules, listing and manufacturer instructions that apply to the actual work.
The service does not automatically include work outside this boundary: Plug strips are discussed as supplemental, not equivalent.
- Service versus feeder installation point
- Available breaker space and equipment compatibility
- Indoor or outdoor enclosure requirements
- Existing grounding, bonding and service condition
What to expect from the completed service
Landmark explains the supported findings and the proposed correction before additional work begins. Flat-rate options identify the approved electrical scope and known exclusions.
After approved work, the electrician tests or operates the completed portion where appropriate, reviews relevant controls or safety information and identifies any remaining responsibility that belongs to the utility, customer, manufacturer or another trade.
Codes and standards that apply
These references explain the framework for this work. The adopted code, Michigan amendments, local authority, utility rules, equipment listings and manufacturer instructions must be considered together for the actual installation.
Frequently asked questions
What is included with whole-home surge protector installation?
The typical scope includes SPD type and rating; conductor routing; breaker connection; status indication; applicable service/feeder rules. The actual proposal identifies the approved equipment, access, permits and property-specific work.
How do I know whether I need whole-home surge protector installation?
Install service- or panel-level surge protective devices. An on-site evaluation confirms whether this focused service, a repair in another category or a broader system correction fits the actual condition.
Will Landmark check the existing electrical system first?
Yes. Landmark reviews the accessible source, protection, conductors, connections and equipment information relevant to the approved evaluation. Concealed or unrelated systems are not represented as inspected unless the scope includes them.
What can change the final price or method?
Existing capacity, route and access, concealed conditions, equipment specifications, permit requirements and the following service boundary can affect the option: Plug strips are discussed as supplemental, not equivalent.
Can I receive a price before authorizing the work?
Yes. Landmark presents a flat-rate option after evaluating the actual condition and before additional approved work begins. The $79 dispatch and evaluation charge is waived when approved work proceeds during the visit.
Technical review
Reviewed by Landmark Electric
This service information was reviewed for scope, safety context and accuracy by Landmark Electric, Inc., Michigan Electrical Contractor License #6114673. It provides general planning information; the adopted rules, local authority, utility requirements, equipment instructions and actual field conditions control each project.
What your service visit includes
Your $79 dispatch and evaluation charge covers sending an electrical professional to your property and the initial on-site evaluation. During that evaluation, the electrician examines the relevant accessible system, shows or explains the supported findings and identifies the cause when the available evidence reasonably allows. Clear, flat-rate options are presented before approved work begins, and the charge is waived when you proceed with approved work during the visit. Any special access, extended diagnosis, permit or after-hours considerations are explained before work moves forward.